- Altium Jtag Over Usb Driver Download For Windows 8.1
- Altium Jtag Over USB Driver Download For Windows
- Altium Jtag Over Usb Driver Download For Windows 7
JTAG Live, the easy-to-use and extremely economic printed circuit board debug tool, from JTAG Technologies. Small price, big performance. Get a free JTAG Maps for Altium license. JTAG Maps is an extension to Altium Designer EDA system that allows the user/engineer to quickly assess the capabilities of the JTAG devices on their design. Until now engineers could often spend hours highlighting the boundary-scan nets of a design manually to determine fault coverage. I am looking for someone who can design FPGA mining bitstreams. I'm looking for someone who can work with me long term. This is a very serious project. Use vivado to a makea bitstream for vu9p fpga card with pcie,like xilinx vcu1525 and make a mining software compatible with windows/linux that works with the JTAG/UART interface over USB. The second is the Android companion app which will be coded to work over Bluetooth to give the slider an easy user interface. A simple android wear companion app is also planned. The third will come much later which is a PC app to control the slider over USB or Bluetooth. Get the answers you need at your own pace with the support options. We’ve got what you need to make the most of your experience with Altium.
Problem:
I have a Studio V7 with a ICE Mk II and mega2560 with a squid cable running fine for years on win 10.
I bought a second new smaller AT-ATMEL-ICE. I disconnected the 10 pin female IDC with squid and moved it to the new small ICE adapter board, and pointed Studio/project/tools to it.
Both MK II and ICE are to used with the JTAG interface for advanced debug over an ISP interface.
The new ICE failed to work !!!
Studio gave message 'Failed to launch program', 'Error: Target power not connected. Debugger command setParameter failed'.
The ICE showed it had power(center red LED on) and the target had power (left Green LED on). obviously the squid was connected properly.
A double check of the squid (unchanged for years) showed pin 4 VTG was connected to VCC as required for Mega2560. VCC measured by voltmeter showed 4.97 V close enough to 5.00V !
If you have this problem, double check VGT like I did. These 3 observation are in direct conflict with the printed Studio V7 error message, which is miss leading as to fault. VTG is used by ICE to program the target micro at it's required proper voltage by ICE.
Altium Jtag Over Usb Driver Download For Windows 8.1
Solution:
I first removed Visual Micro extension from Studio 7.. not certain this was necessity but it was installed after Mk II and before ICE... it is perhaps too conservative.
Next you MUST unplug all Atmel manufactured devices form USB to win 10 PC. This was JTAG-Mk II ICE and Atmel-ICE. MOST IMPORTANT STEP. during the following StudioV7 re install, if anything Atmel is USB connected to PC, the required driver will not be installed properly Uutomatically.
Use Win 10 / Settings / Apps and uninstall all Atmel Apps, yes all of them
Restart win 10
Be sure all Atmel ICE(s) are unplugged from USB ports... so important !!
Go to Atmel web and down load Studio V7 and install it.
Run Studio 7.
My ATMEL-ICE was just purchased by me, even so the date of manufacture was a year ago (bought from element14).
Altium Jtag Over USB Driver Download For Windows
A window popped up and said 'updating ICE firmware', wow I felt progress! the driver was found because the PC was talking to the ICE.
I opened the solution that I was working with old Mk II with the new ICE attached and it worked... / Debug / 'Start_Debug_and_Break' and executed it. It worked
Note:
The ATATMEL-ICE manual says to look at windows device manager (File Explorer then 'This PC'.. right click...Device Manager... Human Interface Devices .. and should see the Atmel device listed in HID.. this did not happen for me.. but if you count the number of HID device in the list, one more will appear and then disappear as you USB connect and then disconnect to PC the ATMEL ICE.
I spent a day of time searching for a solution, as well as calls to tech support at Newark.. I hope this helps someone with the Atmel Studio V7 error message unrelated to the real issue !
ED
Altium Jtag Over Usb Driver Download For Windows 7
Niwot_Dude